Government of Canada navigation bar

Symbol of the Government of Canada

Primary site navigation bar

Certificate 9209

Downloadable version

Canadian flag
Transport
Canada
Safety and Security

Transport Dangerous
Goods Directorate
330 Sparks Street
Ottawa, Ontario K1A 0N5
Transports
Canada
Sécurité et sûreté

Direction générale du
transport des marchandises dangereuses
330, rue Sparks
Ottawa (Ontario) K1A 0N5

Equivalency Certificate

(Approval issued by the competent authority of Canada)

Certificate No.: SU 9209 (Ren. 6)

Certificate Holder: Structural Composites Industries,

a Worthington Cylinders Company

Mode of Transport: Road, Rail, Air, Marine

Issue Date: March 22, 2017

Expiry Date: April 30, 2022

CONDITIONS

This Equivalency Certificate authorizes Structural Composites Industries, a Worthington Cylinders Company, to manufacture, sell, offer for sale, distribute or deliver in Canada, and authorizes any person to handle, offer for transport, transport or import into Canada, by road or railway vehicle, by aircraft or by ship, cylinders in a manner that does not comply with sections 5.1, 5.2, subparagraphs 5.10(1)(a)(ii), 5.10(1)(b)(iii), 5.10(1)(c)(ii), 5.10(1)(d)(iii), and subsection 5.10(2) of the Transportation of Dangerous Goods Regulations, if:

(a) subject to conditions (b) to (f) of the Equivalency Certificate, the requirements with respect to specification TC-3FCM cylinders in CSA Standard B340-08, "Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, Class 2", March 2008, cited in the rest of the certificate as CSA B340-08 are complied with;

(b) each cylinder contains one of the following dangerous goods:

PIN Dangerous Goods

un1002 Air, compressed, with not more than 23.5 % oxygen, by volume

UN1066 Nitrogen, compressed

UN1072 Oxygen, compressed

UN1956 Compressed gas, n.o.s. (mixture of oxygen & air or nitrogen)


Equivalency Certificate

(Approval issued by the competent authority of Canada)

SU 9209 (Ren. 6)

CONDITIONS

(c) each cylinder containing oxygen complies with Clause 4.6.1.2 of CSA B340‑08;

(d) each cylinder is packaged in accordance with Clause 4.9 of CSA B340-08;

(e) each cylinder is stored in a protective environment for use in one of

the following services:

· aircraft escape slide

· back-up crew oxygen

· walk around oxygen

· naval liferaft;

(f) not more than 15 years has elapsed since the initial test date for each cylinder;

Manufacture

(g) the cylinders are manufactured at 336 Enterprise Place, Pomona, CA, U.S.A., in accordance with the specific procedures and with model nos. ALT 215, ALT 279, ALT 280, ALT 281, ALT 282, ALT 372, ALT 405, ALT 621, ALT 63A or ALT 565, filed by Structural Composites Industries, a Worthington Cylinders Company with the Executive Director, Regulatory Frameworks and International Engagement, Regulatory Affairs Branch, Transportation of Dangerous Goods Directorate, Transport Canada;

(h) subject to conditions (i) to (l) of the Equivalency Certificate, the cylinders are in compliance with the applicable requirements for specification TC‑3FCM in CSA Standard B339-08, "Cylinders, spheres, and tubes for the transportation of dangerous goods", March 2008, cited in the rest of this certificate as CSA B339‑08;

(i) the filament material is composed of high modulus para-aramid in accordance with the Society of Automotive Engineers, Inc., aerospace material specification AMS 3901, Organic Fiber (Para-Aramid), Yarn and Roving, High Modulus, dated September 1998, including the applicable supplementary detail specifications thereto;


Equivalency Certificate

(Approval issued by the competent authority of Canada)

SU 9209 (Ren. 6)

CONDITIONS

(j) the para-aramid filament is tested for strand strength in accordance with the American Society for Testing and Materials test method ASTM D2343-03, Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics, published in 2003, and the filament strand strength is at least 3100 MPa;

(k) the cylinder for the gunfire test is positioned so that the projectile impacts the cylinder bottom and exits at the side wall, or so that the projectile impact point is in the cylinder side wall wrapping at approximately a 45º angle and aimed to exit at the cylinder side wall, or so that the projectile impacts the cylinder side wall at a 90° angle to the side wall axis, and any evidence of fragmentation failure of the tested cylinder or any tear greater than 76.2 mm from the entrance or the exit hole is cause for rejection;

(l) the Transport Canada mark, the specification designation and the service pressure marked on each cylinder is: "TC‑SU 9209", followed by service pressure expressed in bar;

(m) the requalification period is 5 years; and

(n) the certificate holder reports any incident involving loss of contents or failure of the cylinders to the Executive Director, Regulatory Frameworks and International Engagement, Regulatory Affairs Branch, Transportation of Dangerous Goods Directorate, Transport Canada.


Equivalency Certificate

(Approval issued by the competent authority of Canada)

SU 9209 (Ren. 6)

CONDITIONS

This Equivalency Certificate serves as the registration of Structural Composites Industries LLC, pursuant to Clause 25.2 of CSA B339-08, to manufacture cylinders of the designs specified herein. Structural Composites Industries LLC's, registered mark pursuant to CSA B339-08, is:

ALT

Note: The issuance of this Equivalency Certificate in no way reduces the certificate holder's responsibility to comply with any other requirements of the Transportation of Dangerous Goods Regulations, the Technical Instructions for the Safe Transportation of Dangerous Goods by Air, the International Maritime Dangerous Goods Code, and the Canadian Aviation Regulationsnot specifically addressed in this certificate.

Signature of Issuing Authority

_____________________________

David Lamarche P. Eng., ing.

Chief

Approvals and Special Regulatory Projects


Equivalency Certificate

(Approval issued by the competent authority of Canada)

SU 9209 (Ren. 6)

(The following is for information purposes only and is not part of the certificate.)

Contact Person: Teofilo A. Naces

Structural Composites Industries

a Worthington Cylinders Company

336 Enterprise Place

Pomona, CA 91768

USA

Telephone: 909-594-7777 / 909-444-2537

Facsimile: 909-594-3939

E-mail: teofilo.naces@worthingtonindustries.com

Explanatory Note

The cylinders have previously been manufactured under Permit SU 4237. The applicant had demonstrated that the substitution of high modulus para-aramid for Type-S fibreglass filament as described would result in a cylinder which could be used with equivalent safety to that of a TC-3FCM specification cylinder. This certificate authorizes an extension of the requalification period to 5 years for cylinders contained in a protective environment.

Legend for Certificate Number

SH - Road, SR - Rail, SA - Air, SM - Marine

SU - More than one Mode of Transport

Ren. - Renewal


Equivalency Certificate

(Approval issued by the competent authority of Canada)

SU 9209 (Ren. 6)

NOTE

Under Canadian Law, a foreign manufacturer of non-specification cylinders cannot be charged with an offence under the Transportation of Dangerous Goods Act, 1992 for failure to comply with the conditions of an Equivalency Certificate. However, certain remedies under the Act are available to Transport Canada in this eventuality.

These include:

1. detention of dangerous goods and consequently the means of containment containing them (subsection 17(1));

2. detention of the means of containment whether full or empty

(subsection 17(1));

3. directions not to import the means of containment or to return them to origin (subsection 17(3));

4. inspectors' directions (section 19);

5. directions to importers of the means of containment to issue notices of defective construction or recall (subsection 9(2)); and

6. revocation of the Equivalency Certificate, thereby making any use of the means of containment an offence (subsection 31(6)).

If none of the foregoing are adequate, Protective Directions may be issued to prohibit or to control the use of the means of containment (section 32).



The following document is available for downloading or viewing:

To access the Word document (DOC) version you must have a DOC reader installed. If you do not already have such a reader, there are numerous DOC readers available for free download or for purchase on the Internet:

Date modified:
2017-06-19